06-H3CWX系列AC+FitAPAP自动升级版本典型配置举例

H3C WX系列AC+Fit AP AP⾃动升级版本典型配置举例关键词：AP, AC, LWAPP缩略语：

⽬录

1特性简介 (1)1.1 特性优点 (1)2应⽤场合 (1)3注意事项 (1)

4 AP⾃动升级版本的典型配置举例 (1)4.1 组⽹需求 (1)4.2 配置思路 (2)4.3 使⽤版本 (2)1. AC版本 (2)2. AP版本 (3)4.4 操作步骤 (3)1. 确认⽹络状况良好 (3)

2. 从FTP Server上获取最新版本 (5)3. 保存配置，并重新启动AC (5)4. AP将⾃动从AC上⾯获取最新版本 (5)4.5 验证结果 (7)5相关资料 (8)

5.1 相关协议和标准 (8)5.2 其它相关资料 (8)1 特性简介

AP版本⾃动升级功能，可以实现，⼈⼯升级AC后，AP检测到AC的版本已经更新，会⾃动从AC上获取最新的相应版本，更新到最新版本。1.1 特性优点

降低了管理AP的⼯作量。2 应⽤场合

这个特性，当有⼤量AP需要升级版本或者AP布置在⽐较难于触及的地⽅时，有极⼤的⽅便性。

3 注意事项

Bootrom版本要能够兼容新的AP版本。4 AP⾃动升级版本的典型配置举例4.1 组⽹需求

本配置举例中的AC使⽤的是WX5002⽆线控制器，AP使⽤的是WA2100⽆线局域⽹接⼊点。图4-1AP⾃动升级版本的典型配置举例组⽹图

4.2 配置思路需要配置以下内容：

●版本升级前，AP和AC处于正常⼯作状态。

●保存AC的配置，并设置默认启动配置；然后从版本服务获取最新的AC和AP的版本到AC上⾯来，AP的名称应符合要求，例如Fit AP WA2100的升级版本名称，必须为wa2100.bin。●重启AC之后，AP将会进⾏版本检测，⾃动升级版本；并重新恢复保存的配置。4.3 使⽤版本1. AC版本display version

H3C Comware Platform Software

Comware Software, Version 5.00, ESS 1102P01

Copyright (c) 2004-2007 Hangzhou H3C Tech. Co., Ltd. All rights reserved.H3C WX5002-128 uptime is 0 week, 0 day, 0 hour, 3 minutesCPU type: BCM MIPS 1250 700MHz1024M bytes DDR SDRAM Memory32M bytes Flash MemoryPcb Version: ALogic Version: 1.0

Basic BootROM Version: 1.12Extend BootROM Version: 1.13

[SLOT 1]CON (Hardware)A, (Driver)1.0, (Cpld)1.0[SLOT 1]GE1/0/1 (Hardware)A, (Driver)1.0, (Cpld)1.0[SLOT 1]GE1/0/2 (Hardware)A, (Driver)1.0, (Cpld)1.02. AP版本_display version

H3C Comware Platform Software

Comware Software, Version 5.00, ESS 1102P01

Comware Platform Software Version COMWAREV500R002B35D004H3C WA2100 Software Version V100R001B05D004

Copyright (c) 2004-2007 Hangzhou H3C Tech. Co., Ltd. All rights reserved.Compiled Jun 12 2007 15:52:46, RELEASE SOFTWAREH3C WA2100 uptime is 0 week, 0 day, 0 hour, 0 minuteCPU type: ATHEROS MIPS 2313 180MHz32M bytes SDRAM Memory4M bytes Flash MemoryPcb Version: Ver.B

Basic BootROM Version: 1.08Extend BootROM Version: 1.08

[SLOT 1]CON (Hardware)Ver.B, (Driver)1.0[SLOT 1]RADIO1/0/1 (Hardware)Ver.B, (Driver)1.0[SLOT 1]ETH1/0/1 (Hardware)Ver.B, (Driver)1.04.4 操作步骤1. 确认⽹络状况良好

需要确认⽹络状况，AC和AP之间的⽹络能够通畅，保证AC和AP在没有升级版本时，能够成功连接。display wlan ap all

Total Number of APs configured: 1Total Number of APs connected : 1AP Profiles

------------------------------------------------------------------AP Name APID State Model Serial-ID------------------------------------------------------------------testap 1 Run WA2100 x028652

------------------------------------------------------------------display wlan ap all verboseTotal Number of APs configured: 1

Total Number of APs connected : 1AP Profile: testap

--------------------------------------------------------------------APID : 1

Up Time(hh:mm:ss) : 00:00:27Model : WA2100Serial-ID : x028652IP Address : 202.1.1.2H/W Version : Ver.B

S/W Version : V100R001B05D004Boot-Rom Version : 1.08Description : -NA-Echo Interval(s) : 10

Statistics report Interval(s) : 600Cir(Kbps) : -NA-Cbs(Bytes) : -NA-Jumboframe Threshold : Disable

Configuration Failure Count : -NA- Last Failure Reason : -NA-Last Reboot Reason : Tunnel Initiated ------------------------------------------------------------------AP Mode : Split

Maximum Number of Radios : 1Current Number of Radios : 1

Client Keep-alive Interval : Disable Client Idle Interval(s) : 3600Broadcast-probe Reply Status : Enable Radio 1:Basic BSSID : 000f-e255-f0Current BSS Count : 2Running Clients Count : 0Wireless Mode : 11bConfigured Channel : auto(3)Configured Power (dBm) : 14Preamble Type : shortRadio Policy : testrp

Service Template : 1 (SSID: market_department) Admin State : UPPhysical State : UPOperational Rates (Mbps):

1 : mandatory2 : mandatory

Radar detected Channels : None

------------------------------------------------------------------2. 从FTP Server上获取最新版本

在AC上，使⽤FTP Client的功能，登陆FTP Server后，使⽤get命令，把需要最新AC和AP 版本（B05D005），例如wx5002.bin 和wx2100.bin，都下载到AC的Flash中。这时需要注意，不能更改AP的启动⽂件名称。dir

Directory of flash:/1 -rw- 5055 Jun 12 2007 09:10:17 config.cfg

2 -rw- 1879880 Jul 25 2007 15:27:34 wa2100.bin3 -rw- 68272 Jun 04 2007 13:29:42 wx5002.bin69662 KB total (199 KB free)3. 保存配置，并重新启动AC

保存当前配置，设置最新版本的wx5002.bin为默认启动⽂件,然后重新启动AC。boot-loader file wx5002_.bin main

This command will set boot file, Continue? [Y/N]:y

The specified file will be used as the main boot file at the next reboot!save config.cfg

The current configuration will be saved to flash:/config.cfg. Continue? [Y/N]:yflash:/config.cfg exists, overwrite? [Y/N]:yNow saving current configuration to the device.

Saving configuration flash:/config.cfg. Please wait... ...............Configuration is saved to flash successfully.startup saved-configuration config.cfgPlease wait ............. Done!reboot

Start to check configuration with next startup configuration file, please wait .........Checking is finished!This will reboot device. Continue? [Y/N]:y4. AP将⾃动从AC上⾯获取最新版本

这时，AP将通过CAPWAP隧道⾃动获取最新版本，并⾃动重启，使其⽣效。⽤命令display version 查看AC的版本信息，已经显⽰为B05D005。⼤约2分钟左右，可以看到AP已经成功重新连接，并且版本已经更新为最新版本。_ version

H3C Comware Platform Software

Comware Software, Version 5.00, Release 1103

Comware Platform Software Version COMWAREV500R002B35D005H3C WX5002-128 Software Version V100R001B05D005

Copyright (c) 2004-2007 Hangzhou H3C Tech. Co., Ltd. All rights reserved.H3C WX5002-128 uptime is 0 week, 3 days, 18 hours, 0 minuteCPU type: BCM MIPS 1250 700MHz1024M bytes DDR SDRAM Memory32M bytes Flash MemoryPcb Version: ALogic Version: 1.0

Basic BootROM Version: 1.13Extend BootROM Version: 1.14

[SLOT 1]CON (Hardware)A, (Driver)1.0, (Cpld)1.0[SLOT 1]GE1/0/1 (Hardware)A, (Driver)1.0, (Cpld)1.0[SLOT 1]GE1/0/2 (Hardware)A, (Driver)1.0, (Cpld)1.0[SLOT 1]M-E1/0/1 (Hardware)A, (Driver)1.0, (Cpld)1.0display wlan ap all verbose

Total Number of APs configured: 1 Total Number of APs connected : 1 AP Profile: testap-----------------------------------------------------APID : 1

AP Name : testapState : Run

Up Time(hh:mm:ss) : 00:00:27Model : WA2100Serial-ID : x028652IP Address : 202.1.1.2H/W Version : Ver.B

S/W Version : V100R001B05D005Boot-Rom Version : 1.08Description : -NA-Echo Interval(s) : 10

Statistics report Interval(s) : 600Cir(Kbps) : -NA-Cbs(Bytes) : -NA-Jumboframe Threshold : Disable

Configuration Failure Count : -NA- Last Failure Reason : -NA-Last Reboot Reason : Tunnel Initiated -----------------------------------------------------Current Number of Radios : 1

Client Keep-alive Interval : Disable Client Idle Interval(s) : 3600Broadcast-probe Reply Status : Enable Radio 1:Basic BSSID : 000f-e255-f0Current BSS Count : 2Running Clients Count : 0Wireless Mode : 11bConfigured Channel : auto(3)Configured Power (dBm) : 14Preamble Type : shortRadio Policy : testrp

Service Template : 1 (SSID: market_department) Admin State : UPPhysical State : UPOperational Rates (Mbps):1 : mandatory2 : mandatory5.5 : supported11 : supported

Radar detected Channels : None-----------------------------------------------------4.5 验证结果

# 在AC上查看AP状态，确认已经处于连接状态，并且ESS⼝处于UP状态display wlan ap all

Total Number of APs configured: 1Total Number of APs connected : 1AP Profiles

------------------------------------------------------------------AP Name APID State Model Serial-ID------------------------------------------------------------------testap 1 Run WA2100 x028652

------------------------------------------------------------------display brief interface

The brief information of interface(s) under route mode:

Interface Link Protocol-link Protocol type Main IPM-E1/0/1 UP DOWN ETHERNET --NULL0 UP UP(spoofing) NULL --Vlan1 UP UP ETHERNET 202.1.1.10

The brief information of interface(s) under bridge mode:Interface Link Speed Duplex Link-type PVIDGE1/0/1 UP 1G(a) full(a) trunk 1WLAN-ESS1 UP -- -- access 1WLAN-DBSS1:1 UP -- -- access 15 相关资料5.1 相关协议和标准⽆

5.2 其它相关资料

《H3C WX系列⽆线控制产品⽤户⼿册》